Don't mind the mess!
We're currently in the process of migrating the Panda3D Manual to a new service. This is a temporary layout in the meantime.
You may be familiar with image file formats like JPEG, which can compress image data dramatically and make image files much smaller than they would be otherwise, in return for sacrificing a tiny bit of the original image quality.
JPEG compression only applies onto to the image size on disk, however. Once you load a texture image into memory, whether it came from a JPEG, PNG, or TGA file, it always takes up the same amount of texture memory on your graphics card (based on the size of the texture).
There is a different option, however, for compressing texture images in-memory. Most modern graphics cards can use a handful of run-time compression algorithms to render directly from a texture that has been compressed in-memory. This is called block compression. It's not really very much like JPEG compression internally, but you can think of it in the same way. It does have some things in common: it reduces the size of the image dramatically (4 times or even 8 times smaller), and it sacrifices a tiny bit of image quality.
Most block compression methods (such as DXT and 3Dc) operate on blocks of 4 by 4 pixels. Therefore, it is recommended that your texture size is a multiple of 4 in both dimensions, or extra padding will have to be applied.
Runtime texture compression
The easiest way to enable compressed texture images is to put the following in your Config.prc file:
This will ask your graphics driver to compress each texture as it loads. This means it takes a tiny bit longer to load each texture, but the resulting texture will take up much less space in texture memory.
There's one important advantage to compressing the textures at runtime this way: the graphics driver will be able to compress all the textures using whatever texture compression algorithm it understands, DXT or otherwise. Not all graphics cards support all compression algorithms, so using this option allows the driver to choose the best algorithm it supports. If the graphics driver doesn't support any compression algorithms at all, it will simply load the textures uncompressed. Either way, your application will still run and all of your textures will be visible.
TXO file format
Panda has a native file format for storing texture images, called TXO (the abbreviation is for "texture object"). This is similar to BAM files. A TXO file contains all of the texture image data in a format very similar to Panda's internal representation, so it loads into memory very quickly.
More importantly, perhaps, TXO files can optionally store pre-compressed texture images. You can use the command:
egg2bam -txo -ctex model.egg -o model.bam
to convert your model to a BAM file, and all of its textures to TXO files, with the image data pre-compressed within the TXO file so that it will not need to be compressed at runtime later. (You may need to specify "pandagl" instead of "pandadx9" as your rendering engine while you run the egg2bam command--at the time of this writing, there were issues with using Panda's DirectX driver in an offline mode like this. However, the resulting TXO files will load on either OpenGL or DirectX at runtime.)
TXO files have the same drawbacks as BAM files: they are tied to a particular version of Panda, so you may need to regenerate them when you next upgrade your Panda version.
A bigger drawback to storing pre-compressed texture images this way is that not all graphics cards support all kinds of DXT compression, and if you try to load a TXO file that a graphics card doesn't understand, Panda3D will decompress the texture on the CPU before uploading it to the graphics card. Thus, pre-compressing all of your textures may cause a loss of texture quality on older cards.
Note that decompression is only available if Panda3D has been compiled with support for the libsquish library; if not, the texture will fail to load entirely if the driver does not support the requested compression mode.
DDS file format
In addition to Panda's native TXO file format, there is a fairly standard format called DDS, which has some of the same properties of TXO. Like TXO, you can store pre-compressed images in a DDS file. The biggest advantage of the DDS file format is that there are already several tools available on the internet to generate DDS files, including GIMP and Photoshop plugins.
Generating your own DDS files has several advantages; chief among them is that you have complete control over the compression artifacts of your texture and can result in less loss of quality since slower compression techniques may be used. However, it has the same issues as storing pre-compressed texture images in TXO files: there is a possibility some graphics cards don't support the texture compression you have used, in which case the texture will have to be decompressed before it can be loaded.
There is a compromise between dynamic compression and pre-compressed textures: you can ask Panda to compress textures on the fly, and then save the resulting compressed image to a TXO file on disk. The next time you load that particular texture, it will load quickly from its TXO file. Since the TXO file was generated by the user's graphics driver, it will presumably use a supported compression algorithm.
To enable this feature, simply insert the following lines in your Config.prc file:
compressed-textures 1 model-cache-dir /c/temp/panda-cache model-cache-compressed-textures 1
Where model-cache-dir specifies any folder on the disk (it will be created if it doesn't already exist). Note that the model-cache-dir may already be specified; the default distribution of Panda specifies a model-cache to speed up loading bam files.
Like DDS file format, the model-cache-compressed-textures variable isn't available in Panda3D versions prior to 1.6.Previous Top Next